1. Inspection and adjustment of wear or damage Ball screw nut pair transmission is widely used in CNC machine tools.

During use, the screw nut will experience varying degrees of wear, deformation, looseness and displacement, which directly affects the processing accuracy of the machine tool.

Therefore, it must be inspected, adjusted and repaired regularly to restore it to the specified accuracy requirements.

(1) Lubrication and sealing protection of screws and nuts.

Used for most screws that are exposed to the outside for a long time, have poor dust-proof conditions, and are easily prone to abrasive wear.

Therefore, during daily maintenance, not only should the screw be cleaned and checked for damage, but the rod and nut should also be cleaned regularly, the oil circuit should be checked and dredged, and the lubrication effect should be observed.

(2) The impact of the axial movement of the screw on the movement accuracy of the driven components is much greater than the radial runout of the screw.

Therefore, in the machine tool accuracy standards, the axial movement of the screw has There are strict requirements for all movements.

Table 8-1 Tolerance of axial movement of the screw of several lathes (unit: mm) Machine tool name Inspection standard number Screw axial movement tolerance Horizontal lathe GB/T4020-1997 sDa≤800 , 0.015 screw lathe 0.002 thread grinder 0.002 Note: sDa is the maximum workpiece rotation diameter allowed by the lathe

If the axial movement of the screw is found to exceed the tolerance during the inspection, it is necessary to further check the pre-axial load condition (such as whether the fastening nut at the end of the screw is loose or not) and the wear condition of the thrust bearing so that appropriate measures can be taken. Adjust or replace.

(1) Bending of the screw After long-term use, some longer screws will bend. For example, if the bed guide rail or slide guide rail of a horizontal lathe is worn and the slide box together with the opening and closing nut sinks, the screw often only meshes with the upper half of the opening and closing nut when working, and there is a considerable gap with the lower half. 

The effect of this radial force will cause the screw to bend and deform. When the bending is severe, it will cause stiffness in the transmission and torsional vibration, affecting the cutting stability and processing quality. During inspection, rotate the screw and use a dial indicator to more accurately measure the bending amount of the screw. If it is out of tolerance, it should be straightened in time (such as pressure straightening and percussion straightening).

Internal stress should be eliminated as much as possible during alignment. A low-temperature treatment process can be added to reduce threading and re-deformation during use.

(2) The gap between the screw and nut. The nut in the sliding screw nut pair is generally made of cast iron or tin bronze, and has greater wear than the screw.

With the continuous wear of the screw and nut spiral surfaces, the shaft of the screw and nut will The clearance increases accordingly. When the gap exceeds the tolerance range, the gap should be adjusted in time for double-nut structures with automatic clearance elimination mechanisms (such as horizontal feed screw nut pairs on horizontal lathes); for structures without automatic clearance elimination mechanisms, the gap should be adjusted in time. The nut should be replaced in time.

1) Wear of the screw The threaded part of the screw wears very unevenly over the entire length. Parts that are frequently used have greater wear.

For example, the longitudinal feed screw of a horizontal lathe has serious wear in the part close to the spindle box, and close to the main spindle box. The foot of the bed shows very little wear.

This causes the screw threads to have different thicknesses and pitches, causing the cumulative screw pitch error to exceed the tolerance, resulting in inaccurate feed amounts of the machine tool feed mechanism, which directly affects the movement accuracy of the workbench or tool holder. When the screw pitch error is too large to meet the machining accuracy requirements, the screw pair can be repaired or replaced with a new one by remachining the thread and using it as a nut.

2) The support and bracket of the screw screw bear a small load in the radial direction and a low rotation speed, so copper sleeves are often used for support; while the accuracy and stiffness of the axial support are much higher than those of the radial support, so high-precision screws are often used. Thrust bearing.

Due to limitations in processing and assembly accuracy, there is often an error in adjusting the perpendicularity of the nut end face and the thread axis, causing the thrust to be concentrated on a part of the bearing, aggravating wear and becoming the main cause of screw vibration. Therefore, when performing regular inspections of the screw pair, attention should be paid to the wear of each support to ensure that the nut end face is in uniform contact with the washer. This ensures the accuracy requirements of the screw axial support, as shown in Figure 8-1.

For long screws installed horizontally, brackets are often used to support the screw to prevent the screw from deflecting due to its own weight. During use, the bracket will inevitably be worn. Therefore, it is also necessary to check regularly for adjustment or repair.