In our previous article, we covered the troubleshooting of abnormal noise in ball screws and the upgrade solutions for quiet ball screws. However, even after resolving noise issues, many machines still experience problems such as inaccurate ball screw positioning , poor repeatability, and dimensional deviations in cutting. These issues are typically not caused by noise, but by a more concealed fault: excessive backlash.
As the leading cause of positioning accuracy failure in ball screws, backlash directly affects the finished product precision of CNC machines, robotic arms, 3D printers, and automated equipment. In this article, we focus on analyzing the causes of backlash, inspection methods, and on-site repair techniques.
I. What is Ball Screw Backlash

Backlash refers to the lost motion that occurs when the ball screw reverses direction, during which the nut does not immediately follow the movement.

Simple explanation:

When rotation stops in the forward direction and starts in reverse, the small “dead travel” in between is backlash.

Common control ranges (engineering reference values):

  • Precision equipment: ≤ 1–2 μm
  • General industrial equipment: ≤ 3–5 μm

When backlash exceeds 5 μm, high-precision positioning systems will typically show obvious positioning errors or reduced repeatability.

TBI SFA2510-3.8 Dust-Proof Ball Screw SFA2510 Ball Screw
II. Typical Symptoms of Excessive Backlash

During actual equipment operation, excessive backlash results in the following issues:

  • Normal forward movement, but obvious lag when reversing
  • Failure to accurately return to the origin after repeated reciprocating motion
  • Unstable machining dimensions that vary randomly
  • Contour errors during interpolated motion
  • Unstable performance even after system parameter compensation

These issues are especially prominent in high-precision equipment such as CNC machine tools.

III. Core Causes of Excessive Backlash

Increased backlash usually results from structural wear or preload failure, including:

  • Decay or failure of preload

    Preload reduction after long-term operation is one of the most common causes.

  • Wear of the screw raceway or steel balls

    Leading to increased fitting clearance.

  • Wear or damage to the ball recirculation system (deflector)

    Causing abnormal clearance and sometimes abnormal noise.

  • Insufficient lubrication or contamination (dust, cutting fluid intrusion)

    Accelerating abnormal wear.

  • Long-term heavy load or high-speed operation

    Speeding up structural fatigue.

  • Installation shock or mechanical collision

    Causing loosening or deformation of internal components.

IV. On-Site Rapid Inspection Method (Practical)

The most common and efficient method is the dial indicator measurement.

Procedure:

  1. Mount the dial indicator on the workbench, with the probe against the screw end or nut.
  2. Drive the motor to rotate forward → reverse.
  3. Observe the “runout” of the dial indicator needle.
  4. This reading is the actual backlash.

Notes:

  • Measurement should be performed at low speed and stable conditions.
  • Test under constant load or no-load conditions if possible.
  • Avoid preload or structural elasticity affecting results.
V. Graded Repair Solutions (On-Site Practical Guide)

Different methods are used based on the amount of backlash:

1.  Mild backlash (1–3 μm)

  • Adjust or restore preload
  • Can usually restore precision quickly

Applicable to: new equipment or lightly worn machinery

2. Moderate backlash (3–8 μm)

  • Replenish grease
  • Readjust the preload structure (e.g., double-nut preload)
  • Repairable in most cases

Applicable to: equipment after moderate service time

3. Severe backlash (>8 μm)

  • Obvious wear of the screw or nut
  • Recommend replacing the ball screw nut or the entire assembly

Commonly seen in: heavy-duty equipment or long-running machinery

Backlash is a core indicator of positioning accuracy, and 80% of reversing positioning problems originate from it. If your equipment has normal backlash after testing, but the accuracy still drifts, the problem is usually in the installation, lubrication, or thermal deformation, which we will discuss in detail in the next article.